ISO 10350-1:2017 PDF

Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials

Open preview (PDF)

Title (English):

ISO 10350-1:2017

Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials

Document status:: Withdrawn
Format:: Electronic (PDF)
Number of pages:: 11
Publication date:: October 11, 2017
Edition:: ISO IS 10350 edition 3 version 1
ICS:: 83.080.20

Delivery type:

Full version25 €Read online 24h10 €Read online 72h15 €

Document language:

enru

Delivery time:Immediate download

Price:25 €

Description (English):

The ISO 10350 series identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented conventionally in manufacturers' data sheets. ISO 10350-1 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness. For the purposes of ISO 10350-1, long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding. NOTE ISO 10350-2 deals specifically with long- or continuous-fibre-reinforced plastics.

Technical details

Technical committee: ISO/TC 61/SC 2 - Mechanical behavior
SKU: ISO 10350-1:2017

Abstract

Overview

ISO 10350-1:2017 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials - defines a standardized way to acquire and present single-point material data for moulding plastics. The standard focuses on comparable, single-value properties commonly shown on manufacturers’ data sheets for unreinforced and reinforced thermoplastic and thermosetting materials that are injection- or compression-moulded or prepared as sheets. It clarifies specimen preparation, conditioning, test requirements and the prescribed format for reporting results so that material comparisons are meaningful and reproducible.

Key topics and requirements

Single-point data scope: Specifies which basic properties should be expressed as single experimental values (or, where applicable, two values under different conditions) for preliminary material selection.
Material coverage: Applies predominantly to moulding materials (thermoplastics and thermosets). Long-fibre-reinforced plastics are defined as having fibre lengths > 7.5 mm prior to moulding (ISO 10350-2 covers long/continuous fibres).
Specimen preparation: Requires use of established moulding or machining procedures (e.g., ISO 294-series for injection moulding, ISO 293/295 for compression moulding, ISO 2818 for machining).
Conditioning rules: For materials insensitive to absorbed water, condition specimens at 23 °C ± 2 °C and 50 % RH ± 10 % for ≥ 88 h (unless a material-specific standard applies). For water-sensitive materials, present data for both dry and 50 % RH conditions with specified exceptions. Store conditioned specimens at 23 °C ± 2 °C for ≥ 16 h before testing.
Test methods and presentation: The standard prescribes the test methods, conditions, units and a table format for presentation (e.g., rheological properties such as MFR use ISO 1133). Report mean values and record moulding parameters and sample provenance; testing on specimens from at least three production samples is recommended.

Practical applications and users

ISO 10350-1 is intended for:

Material suppliers preparing standardized data sheets
Design and product engineers comparing candidate plastics during early-stage selection
Quality and testing laboratories ensuring reproducible single-point test data
Procurement/specification writers requiring comparable property data across suppliers

Typical uses include preliminary material selection, supplier comparison, formulation screening and generating consistent technical data for product datasheets.

Related standards

ISO 10350-2 (long- or continuous-fibre-reinforced plastics)
Complementary multipoint-data standards: ISO 11403‑1, ISO 11403‑2, ISO 11403‑3
Referenced test standards (examples): ISO 1133 (MFR), ISO 527 (tensile), ISO 178 (flexural), ISO 62 (water absorption), ISO 1183 (density), ISO 11357/11359 (thermal analysis)

Keywords: ISO 10350-1, plastics single-point data, moulding materials, material data sheets, specimen conditioning, MFR, test procedures, material comparison.

Related standards

Standards mentioned in the description

Abstract

Overview

Key topics and requirements

Single-point data scope: Specifies which basic properties should be expressed as single experimental values (or, where applicable, two values under different conditions) for preliminary material selection.
Material coverage: Applies predominantly to moulding materials (thermoplastics and thermosets). Long-fibre-reinforced plastics are defined as having fibre lengths > 7.5 mm prior to moulding (ISO 10350-2 covers long/continuous fibres).
Specimen preparation: Requires use of established moulding or machining procedures (e.g., ISO 294-series for injection moulding, ISO 293/295 for compression moulding, ISO 2818 for machining).
Conditioning rules: For materials insensitive to absorbed water, condition specimens at 23 °C ± 2 °C and 50 % RH ± 10 % for ≥ 88 h (unless a material-specific standard applies). For water-sensitive materials, present data for both dry and 50 % RH conditions with specified exceptions. Store conditioned specimens at 23 °C ± 2 °C for ≥ 16 h before testing.
Test methods and presentation: The standard prescribes the test methods, conditions, units and a table format for presentation (e.g., rheological properties such as MFR use ISO 1133). Report mean values and record moulding parameters and sample provenance; testing on specimens from at least three production samples is recommended.

Practical applications and users

ISO 10350-1 is intended for:

Material suppliers preparing standardized data sheets
Design and product engineers comparing candidate plastics during early-stage selection
Quality and testing laboratories ensuring reproducible single-point test data
Procurement/specification writers requiring comparable property data across suppliers

Typical uses include preliminary material selection, supplier comparison, formulation screening and generating consistent technical data for product datasheets.

Related standards

ISO 10350-2 (long- or continuous-fibre-reinforced plastics)
Complementary multipoint-data standards: ISO 11403‑1, ISO 11403‑2, ISO 11403‑3
Referenced test standards (examples): ISO 1133 (MFR), ISO 527 (tensile), ISO 178 (flexural), ISO 62 (water absorption), ISO 1183 (density), ISO 11357/11359 (thermal analysis)

Keywords: ISO 10350-1, plastics single-point data, moulding materials, material data sheets, specimen conditioning, MFR, test procedures, material comparison.

ISO 10350-1:2017 PDF

Technical details

Abstract

Overview

Key topics and requirements

Practical applications and users

Related standards

Related standards

Abstract

Overview

Key topics and requirements

Practical applications and users

Related standards

Related standards

Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plast…

Ships and marine technology — Offshore wind energy — Port and marine operations

Plastics - Preparation of test specimens by machining (ISO 2818:2018)

Adhesives. T-peel test for flexible-to-flexible bonded assemblies

Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 103…

Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11…

Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing proper…

Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on p…