SIST EN ISO 4490:2018 PDF

Metallic powders - Determination of flow rate by means of a calibrated funnel (Hall flowmeter) (ISO 4490:2018)

Title (English):

SIST EN ISO 4490:2018

Metallic powders - Determination of flow rate by means of a calibrated funnel (Hall flowmeter) (ISO 4490:2018)

Document status:: Active
Format:: Electronic (PDF)
Number of pages:: 14
Publication date:: June 15, 2018
Edition:: ISO 4490:2018
ICS:: 77.160

Document language:

enru

Delivery time:1–7 days

Price:60 €

Description (English):

ISO 4490:2018 specifies a method for determining the flow rate of metallic powders, including powders for hard metals, by means of a calibrated funnel (Hall flowmeter). The method is applicable only to powders which flow freely through the specified test orifice.

Technical details

Technical committee: I13 - Imaginarni 13
SKU: SIST EN ISO 4490:2018

Abstract

Overview

EN ISO 4490:2018 (ISO 4490:2018) specifies a standardized test method for measuring the flow rate of metallic powders using a calibrated funnel, commonly called the Hall flowmeter. The method quantifies how long it takes for a 50 g test portion of a freely flowing metallic powder (including powders for hard metals) to pass through a standardized orifice. It applies only to powders that flow freely through the specified test orifice.

Key Topics and Requirements

Principle: Measurement of elapsed time for 50 g of powder to flow through a calibrated funnel (reported as seconds per 50 g).
Apparatus:
- Calibrated funnel (Hall flowmeter) of standardized dimensions made from non‑magnetic, corrosion‑resistant metal with adequate hardness and wall thickness.
- Rigid stand with a vibration‑free base.
- Balance with accuracy of ±0.05 g.
- Timing device with accuracy of ±0.1 s.
- Reference grit (reference powder) for funnel calibration.
Calibration:
- Manufacturer supplies a calibrated funnel. Reference grit is dried at 110 °C for 60 min, cooled in a desiccator, and five determinations are made on 50 g until five values fall within 0.4 s. The average (nominally 40.0 s ± 0.5 s/50 g) is stamped on the funnel.
- Users should periodically verify calibration. If reference flow deviates, a correction factor (40.0 ÷ measured value) may be applied; investigate cause (wear or coating). Discontinue use if reference flow

Related standards

Mentioned in the description and other SIST standards

Overview

Key Topics and Requirements

Principle: Measurement of elapsed time for 50 g of powder to flow through a calibrated funnel (reported as seconds per 50 g).
Apparatus:
- Calibrated funnel (Hall flowmeter) of standardized dimensions made from non‑magnetic, corrosion‑resistant metal with adequate hardness and wall thickness.
- Rigid stand with a vibration‑free base.
- Balance with accuracy of ±0.05 g.
- Timing device with accuracy of ±0.1 s.
- Reference grit (reference powder) for funnel calibration.
Calibration:
- Manufacturer supplies a calibrated funnel. Reference grit is dried at 110 °C for 60 min, cooled in a desiccator, and five determinations are made on 50 g until five values fall within 0.4 s. The average (nominally 40.0 s ± 0.5 s/50 g) is stamped on the funnel.
- Users should periodically verify calibration. If reference flow deviates, a correction factor (40.0 ÷ measured value) may be applied; investigate cause (wear or coating). Discontinue use if reference flow

SIST EN ISO 4490:2018 PDF

Technical details

Abstract

Overview

Key Topics and Requirements

Related standards

Abstract

Overview

Key Topics and Requirements

Related standards

Metallic powders — Determination of flow rate by means of a calibrated funnel (Hall flowmeter)

Method to calculate GHG emissions at LNG plant (ISO 6338:2023)

Additive manufacturing of metals - Powder bed fusion (PBF) - In-situ coaxial photodiode monitoring for lack o…

Facility management - Development of the facility management organization (ISO 41002:2026)

Rigid cellular plastics - Determination of compressive properties (ISO 844:2026)

Processing of health care products - Information to be provided by the medical device manufacturer for the pr…

Ophthalmic optics - Uncut finished spectacle lenses - Part 4: Specifications and test methods for the propert…

Anaesthetic and respiratory equipment - Tracheal tubes and connectors - Amendment 1: Reinstatement of third e…