SIST ISO 1813:2015 PDF

Belt drives - V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts - Electrical conductivity of antistatic belts: Characteristics and methods of test

Title (English):

SIST ISO 1813:2015

Belt drives - V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts - Electrical conductivity of antistatic belts: Characteristics and methods of test

Document status:: Active
Format:: Electronic (PDF)
Number of pages:: 16
Publication date:: February 17, 2015
ICS:: 21.220.10
Technical committee:: DTN - Lift and transport appliances

Document language:

enru

Delivery time:1–7 days

Price:60 €

Description (English):

ISO 1813:2014 specifies the maximum electrical resistance of antistatic endless V-ribbed belts, joined V-belts, and single V-belts including wide section belts and hexagonal belts, as well as corresponding production control and individual proof methods of measurements. The application of ISO 1813:2014 is limited to new belts intended to be used in an explosive atmosphere or in situations where there is a fire risk. The test is intended to ensure that the belt is sufficiently conductive to dissipate charges of electricity which can form on it in service.

Technical details

SKU: SIST ISO 1813:2015

Abstract

Overview

ISO 1813:2014 specifies characteristics and test methods for the electrical conductivity of antistatic V-belts - including V-ribbed belts, joined V-belts, single V-belts, wide section and hexagonal belts. The standard defines maximum electrical resistance limits, production control (factory) tests and laboratory proof tests for new belts intended for use in potentially explosive atmospheres or where fire risk exists. Its purpose is to ensure belts are sufficiently conductive to dissipate electrostatic charge in service.

Key topics and requirements

Scope: Applies to new antistatic belts used where charge dissipation is critical (explosive atmospheres, fire-risk environments).
Electrical measurement principle: Measure resistance along a fixed length with an insulation tester under specified conditions; belts pass if resistance does not exceed limit values (given in Tables 1–3 or by Formula (1)).
Test equipment:
- Insulation tester nominally 500 V d.c. (instrument must be able to apply ≥40 V and ≤3 W to test section); a 1 000 V instrument may be used for resistance > 10 Ω.
- Metal electrodes (preferably brass) with minimum contact width 25 mm and nominal spacing 100 mm; specific grooved electrodes for V-groove and ribbed profiles and movable electrode options for classical/narrow V-belts.
- Belt loading to ensure contact: 1 N per millimetre of nominal belt width (applied per strand for joined belts).
Production control (factory) test:
- Ambient conditioning 15 °C to 30 °C.
- Straighten belt, apply specified load, measure resistance 5 s ± 1 s after applying voltage.
- Number and positions of test points depend on belt length and type (e.g., two points for belts ≤ 2 000 mm; additional points per 1 000 mm).
Proof (laboratory) test:
- Standard atmosphere 23 °C/50 % RH (ISO 23529 conditioning).
- Surfaces cleaned (Fuller’s earth) then covered with conductive coating: either conductive silver lacquer/colloidal graphite (surface resistivity

Related standards

Mentioned in the description and other SIST standards

Abstract

Overview

Key topics and requirements

Scope: Applies to new antistatic belts used where charge dissipation is critical (explosive atmospheres, fire-risk environments).
Electrical measurement principle: Measure resistance along a fixed length with an insulation tester under specified conditions; belts pass if resistance does not exceed limit values (given in Tables 1–3 or by Formula (1)).
Test equipment:
- Insulation tester nominally 500 V d.c. (instrument must be able to apply ≥40 V and ≤3 W to test section); a 1 000 V instrument may be used for resistance > 10 Ω.
- Metal electrodes (preferably brass) with minimum contact width 25 mm and nominal spacing 100 mm; specific grooved electrodes for V-groove and ribbed profiles and movable electrode options for classical/narrow V-belts.
- Belt loading to ensure contact: 1 N per millimetre of nominal belt width (applied per strand for joined belts).
Production control (factory) test:
- Ambient conditioning 15 °C to 30 °C.
- Straighten belt, apply specified load, measure resistance 5 s ± 1 s after applying voltage.
- Number and positions of test points depend on belt length and type (e.g., two points for belts ≤ 2 000 mm; additional points per 1 000 mm).
Proof (laboratory) test:
- Standard atmosphere 23 °C/50 % RH (ISO 23529 conditioning).
- Surfaces cleaned (Fuller’s earth) then covered with conductive coating: either conductive silver lacquer/colloidal graphite (surface resistivity

SIST ISO 1813:2015 PDF

Technical details

Abstract

Overview

Key topics and requirements

Related standards

Abstract

Overview

Key topics and requirements

Related standards

Belt drives — V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts — E…

Rubber — General procedures for preparing and conditioning test pieces for physical test methods

Method to calculate GHG emissions at LNG plant (ISO 6338:2023)

Additive manufacturing of metals - Powder bed fusion (PBF) - In-situ coaxial photodiode monitoring for lack o…

Facility management - Development of the facility management organization (ISO 41002:2026)

Rigid cellular plastics - Determination of compressive properties (ISO 844:2026)

Processing of health care products - Information to be provided by the medical device manufacturer for the pr…

Ophthalmic optics - Uncut finished spectacle lenses - Part 4: Specifications and test methods for the propert…